Uniden BC244CLT Spezifikationen

COVERBC244clt.qxd 3/11/99 11:59 AM Page 1

7Initial Clock Set-up1. When power is initially applied, the display flashes 1122::0000 PPafter ashort delay.2. Enter the time directly by p

8Reset the Clock Time1. After the scanner has been turned on, to reset the clock time, simply press and hold the TIMESETkey. The display digits flash.

Set the Alarm Time1. After the clock time has been entered, press and hold ALARM SET until the timeindicated and AALLAARRMMindicator fl

105.AALLAARRMMindicator and time stop flashing, butremain on.6. The alarm time remains in the display for five seconds, then returns to current tim

11Set the Squelch1. Turn SQUELCHfully clockwise to the highest setting.2. Press ON/OFFto turn on the scanner. 3. Adjust the VOLUME

124. Set the SQUELCHcontrol to AUTOfor the factory setting. Or, manually set squelchas follows: Think of squelch as a gate. Turn SQUELCHfully counter

135. The scanner automatically starts scanning. If you have not programmed any channelsyet, press WXto hear your local weather broadcast.6. Adjust VOL

14Programming FrequenciesBefore you can use your BC244CLT scanner, you must program the channels(except weather frequencies). Follow these steps:Examp

4. Press Eto complete the entry. The channel digits stop flashing.Deleting a Stored FrequencyIf you want to delete a stored frequency, fol

164. The following screen appears.About Memory Back-upYour BC244CLT has a convenient memory back-up system. In the event of a powerfailure, the sca

PrecautionsBefore you read anything else,please observe the following:Unidenand Bearcatare registered trademarks of Uniden America Corporation.The i

17Direct Channel AccessThis feature allows you to instantly access a specific channel you want to monitor.Example: Select Channel 4.1. PressMANUALto e

18Weather Channel ScanThe BC244CLT allows you to search from 7 pre-programmed NOAA channels foryour local NOAA weather channel.Press WXto find the act

19Priority ScanningPriority Scan is like a dual watch function. When you activate Priority Scan mode,the scanner keeps track of the activity on the pr

203. Press and hold PRIORITY until a beep sounds. The PPRRIIindicator appears in the display and Pindicatorappears to the left of the selectedch

21In the Manual mode, press LOCKOUT to lock out the displayed channel. PressingLOCKOUTdoes not advance to the nextchannel in Manual mode.

22Restore all Locked Out ChannelsTo unlock all channels, you must be in Manual Mode.1. Press MANUAL.2. Press and hold LOCKOUTuntil a beep

23Helpful HintsGeneral Use Turn the scanner off before disconnecting the power. Always write down the programmed frequencies in the event of scannerme

24Problem Solution Check the connections at both ends of the AC Adapter. Turn on the wall switch of your room.You could be using an outlet controlled

25If you still cannot get satisfactory results and want additional information, or toreturn the unit for service, please call the Uniden Parts and Ser

26Certified in accordance with FCC Rules and Regulations Part 15 Sub-part C as ofdate of manufacture.Band Coverage: 10 bandsFrequency Coverage: 29.0-2

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1About Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retailowner, this Uniden Produc

28BACK COVERBC244clt.qxd 3/11/99 12:00 PM Page 28

1About ScanningScanning OptionsScanning is easy and fun with the BC244CLT 30-Channel Base Scanner. You canscan in 2 ways: Scan channels you have progr

2You must program a frequency into each channel you want to use. If you do nothave any known local frequencies to program, a Uniden representative sho

3Installing the BC244CLT 1. Insert the small plug at the end of the AC Adapter cord into the AC 10Vjack on the scanner.2. Plug the AC Adapter into any

4Controls and Functions 1. LCD Display Displays time, channel, frequency, and functions. (Page 6)2. Numeric Keys Use to program a frequency into each

59. ALARM Key Turns the alarm mode on or off. 10 AM/PMKey Selects a.m. or p.m. while setting the clock time or alarm time.11. PRIORITYKey Turns Priori

618.AALLAARRMMIndicator Appears when Alarm function is active.19. SSCCAANNIndicator Appears when in Scan Mode.20. PPRRIIIndicator Displays when Priori