Uniden BEARCAT UBC248CLT Bedienungsanleitung

UBC 248CLT• FULLY PROGRAMMABLE• FULL FREQUENCY LCD READOUT• ALARM CLOCK• AM/FM RADIO• CHANNEL LOCKOUT• PRIORITY CHANNEL• SCAN DELAY• MEMORY BACKUP• FR

7Scanning OverviewThe UBC248CLT has 50 memory channels. Each can be programmed to store one frequencywithin the band of frequency coverage. (For a lis

8Initial Clock Set-up1. When power is initially applied, the display flashes i2:00 Pafter ashort delay.2. Enter the time directly by pressing

Set the Squelch1. Turn SQUELCH fully clockwise to the highest setting.2. Press SCANNER to turn on the scanner. 3. Adjust the VOLUME

104. To set the SQUELCH control to AUTO turn fully counter clockwise until control clicks intoplace. Or, manually set squelch as follows: Think of squ

11Programming Tips for Scanner Program one frequency per channel. Channel 1 is the location of the default priority channel. Program the most importan

12Programming Scanner FrequenciesBefore you can use your UBC248CLT scanner, you must program the channels. Follow thesesteps:Example: Program 420.0150

4. Press E to complete the entry. The channel digits stop flashing.Display shows Deleting a Scanner FrequencyIf

144. The following screen appears.About Memory Back-upYour UBC248CLT has a convenient memory back-up system. In the event of a power failure,the sc

To restore the bank number, press the number on the keypad. The bank number appears inthe display..The bank number associated with channel curre

16Direct Channel Access for ScannerThis feature allows you to instantly access a specific channel you want to monitor.Example: Select Channel 4.1. Pre

PrecautionsBefore you read anything else,please observe the following:Uniden®and Bearcat®are registered trademarks of Uniden Corporation.Changes or mo

17To Set the Priority ChannelYour UBC248CLT has one default Priority Channel per bank. Each priority channel is, set atthe first channel in the bank.

18Channel LockoutYou can lock out a channel so it is not scanned. Channel Lockout does not erase the frequencyfrom the channel. You can lock out up to

2. Press LOCKOUT again to unlock the displayed channel. L/Ono longer appears in the display.Restore All Locked Out ChannelTo unlock all channels, you

20To Set Delay in Scan Mode1. Press SCAN.2. When your scanner stops on a channel, press DELAY. DLY appears in the display andscanning resume 2 seconds

21SEARCHINGThe UBC248CLT can search bands or range of frequencies you specify to find desiredfrequencies. This is useful if user does not have a Frequ

22Locking Out Frequencies in SearchDuring search, you might repeatedly encounter frequencies that you are not interested in. Also,all scanners are sub

23LCD BacklightThe LCD Backlight comes on when the power is applied. In Scan Mode and Manual Mode, thebacklight stays on bright continuously. In the o

3. Press ▼ or ▲ to set the desired frequency. The channel number flashes. Continue topress ▼ or ▲ to step through thefrequencies in 100kHz steps. O

25Deleting a Stored Radio FrequencyIf you want to delete a stored frequency, follow these steps:Example: Delete the frequency in Channel 9.1. Press RA

26Reset the Clock Time1. After the scanner has been turned on, to reset the clock time simply press and hold the TIME SETkey. The display digits fla

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1About Scanning . . . . . . . . . . . . . . .

27Set the Alarm TimeThere are two types of alarm sounds with this scanner., Tone Alarm and Radio Alarm. Both typesset the alarm time in the same manne

284. Press E to complete the entry. 5. ALARM indicator and time stop flashing, butremain on.6. The alarm time remains in

29Turn the Alarm OffPress ALARM to deactivate the alarm function. When the alarm is off, theALARM indicator and current alarmtime are no longer displa

30Set Alarm to Radio ModeBefore you set the Radio Alarm, make sure the AM or FM channel is selected and theVOLUME control is set to the desired level.

31Helpful HintsGeneral Use Turn the scanner off before disconnecting the power. Always write down the programmed frequencies in the event of scanner m

32Problem Solution Check the connections at both ends of the AC Adaptor. Turn on the wall switch of your room.You could be using an outlet controlled

33ProblemSolution Scan won’t stop. Adjust squelch to the threshold (Page 9). Check the antenna connection. Check to see if many of the channels are lo

34Band Coverage:8 bands plus and AM/FM RadioFrequency Coverage: Scanner 66-88 MHz VHF Low Band12.5 KHz step137-144 MHz Land Mobile144-148 MHz 2 Meter

Uniden UBC248CLTNote: Please keep your sales docket as it provides evidence of warranty.WARRANTOR: Uniden Australia Pty. Limited ACN 001 865 498Uniden

36

1About ScanningScanning is easy and fun with the UBC248CLT 50-Channel Base Scanner with AM/FM Radio. What is Scanning?Unlike standard AM or FM radio s

THANK YOUFOR PURCHASING THIS UNIDEN PRODUCT!© 2000 Uniden Corporation UBZZ01299BZAll rights reserved

2 Many more in the 66-88MHz, 137-174MHz, and406-512MHz ranges AM/FM radioYou must program a frequency into each channel you want to use. Taking Proper

Installing the UBC248CLT 1. Insert the small plug at the end of the AC Adaptor cord into the AC 10V jack on the scanner.2. Plug the AC Adaptor into an

4Controls and Functions 1. LCD Display Displays time, channel, frequency, and functions. (Page 6)2. Numeric Keys Press to program a frequency into eac

510. DELAY Key Turns Delay function. When Scan stops on a channel it causes scanner to remain on that channel for 2 seconds before the scanning resume

623. ALARM Appears when Alarm function is active. Flashes in the snooze function mode.24. BANK Appears when in Scan Mode, Manual Mode.25. 1-5 In Scan