Friday, November 07, 2008 1 BCD396XT The Complete Reference This document provides a complete reference to all menus, functions, and f
Friday, November 07, 2008 10 Scanning Lockout You can lock out any System, Site, Channel Group, Channel, or search frequency. Locked out channels are
Friday, November 07, 2008 100 Set Delay Time This setting controls how long the scanner stays on Mute Off state after a transmission ends. Turn [Scrol
Friday, November 07, 2008 101 Set Alert Light You can select whether the scanner should have alert light when a tone-out Channel becomes active*. Off
Friday, November 07, 2008 102 Wired Clone Connect two BCD396XTs and select this menu to copy and override all data from one to another. Master Slave T
Friday, November 07, 2008 103 Settings You can set the following items from this menu. Set Backlight Adjust Key Beep Battery Option Adjust Audio AGC A
Friday, November 07, 2008 104 Set Color This option can be used to select the backlight color. Blue Red Magenta Green Cyan Yellow White Press [E / yes
Friday, November 07, 2008 105 Adjust Audio AGC You can set the following items. Analog AGC Digital AGC Press [E / yes / gps] to enter each setting. An
Friday, November 07, 2008 106 Digital AGC This menu lets you set the following items. Response Time Reference Gain Press [E / yes / gps] to enter each
Friday, November 07, 2008 107 Set GPS Format You can set the following items for GPS. Set Pos Format Set Time Format Set Time Zone Set Unit Press [E /
Friday, November 07, 2008 108 Set Serial Port You can set the serial port speed from the following items. 4800 bps 9600 bps 19200 bps 38400 bps
Friday, November 07, 2008 109 Turn [Scroll Control] to focus the cursor on the band you want to change. Then, press [E / yes / gps] to enter the modul
Friday, November 07, 2008 11 Multi-Site System All trunked systems can have more than one site. All sites in the system share the same Channel Groups
Friday, November 07, 2008 110 See Scanner Info This menu lets you see some information about the scanner, including the memory usage. Select from the
Friday, November 07, 2008 111 SCAN MODE Display during Scan Mode The LCD display in Scan mode is as follows. SCAN : This scrolls to the
Friday, November 07, 2008 112 While in the Scan Mode, the first line displays currently scanned system, site or search range name and the second line
Friday, November 07, 2008 113 Scanning Order First, systems belonging to Quick Key 1 are scanned. Then systems that belong to Quick Key 2,…,9,0,11,…19
Friday, November 07, 2008 114 Scanning Operation Quick Key Operation For Conventional Systems, the SQK is set at the system level. However, for trunke
Friday, November 07, 2008 115 Scan for Conventional Systems In conventional scanning, the scanner steps through each unlocked channel. If there is act
Friday, November 07, 2008 116 ID Scan : If a TGID matches a TGID stored in an unlocked channel, the scanner goes to the V-Ch and monitors the transmis
Friday, November 07, 2008 117 ID Display Format The scanner displays received ID in the following format on the second line. Normal ID The scanner dis
Friday, November 07, 2008 118 PATCH ID The scanner displays a PATCH list IDs and received PATCH ID as "ID:xx-xxx yy-yyy". (xx-xxx : One of t
Friday, November 07, 2008 119 Trunking Activity Indicators (Display Mode 3) The scanner shows trunking activity when held on the C-Ch. Press [6 / RIGH
Friday, November 07, 2008 12 Search Lockout You can lock out up to 500 frequencies. The limit of temporary L/O frequencies: 250 The limit of per
Friday, November 07, 2008 120 Location Based Scanning This operation controls the lockout state for each group or site when the scanner is connected t
Friday, November 07, 2008 121 Control Channel Data Stream Output The scanner can output the data stream on the control channel. You can turn on this f
Friday, November 07, 2008 122 [LTR System] LTR,<A>-<GG>-<HH>-<III>-<FF> <A> = Area Number (0 or 1) <G
Friday, November 07, 2008 123 For Motorola system: Decoded Description Remark ,CNM TG-tttt CH-ccc VC-ffffffff Call for Talk Group tttt = Talk Group ID
Friday, November 07, 2008 124 For EDACS system: Decoded Description Remark ,CNM TG-ttt CH-cc VC-ffffffff Call for Talk Group ttt = Talk Group ID (Hex
Friday, November 07, 2008 125 For P25 system: Decoded Description Remark ,IU N-n B-bbbbbbbb S-sss Identifier Update n = Identifier Number bbbbbbbb = B
Friday, November 07, 2008 126 Temporary System Hold *For trunked systems, “system” should be read as “site” in this section. **In Temporary System Hol
Friday, November 07, 2008 127 System Hold Long press [Hold / ] to goes to the System Hold Mode. While on System Hold, the scanner scans only one syst
Friday, November 07, 2008 128 System Select in Scan Hold Mode When you go to Quick Select System from Scan Hold Mode and exit from this state, the sca
Friday, November 07, 2008 129 Key Operation During Scan Normal Mode [Scroll Control] knob Turn this knob to resume scanning while monitoring. Turn thi
Friday, November 07, 2008 13 Dropout Delay Controls whether the scanner pauses at the end of a transmission to wait for a reply. You can set the Delay
Friday, November 07, 2008 130 F+[Scan / srch] key If the current system is a conventional system or search range: ・ Press this key to display the pro
Friday, November 07, 2008 131 SCAN HOLD MODE Press [Hold / ] in Scan Mode to go to Scan Hold Mode. Display while in Scan Hold Mode The display in Sca
Friday, November 07, 2008 132 Press [FUNC] to go to the Function Mode and display the system number tag, channel number tag, IF Exchange and Volume le
Friday, November 07, 2008 133 Hold on a Channel (TGID) in Trunked System: *If there are two or more sites in the system, the same TGIDs will appear in
Friday, November 07, 2008 134 For example, "ID:0-01-063" for the LTR System displays in Channel Name Display Mode 2. Hold on Sys
Friday, November 07, 2008 135 *In Motorola System, System ID is displayed as "SID:xxxxh-yyzz". “xxxxh” means System ID. “yy” means Sub Syste
Friday, November 07, 2008 136 Hold on TalkGroup ID from ID Search / ID Scan The scanner monitors the held TGID continuously. While monitoring a TGID a
Friday, November 07, 2008 137 Store TGID To quickly store a TGID into a channel, enter the TGID using the number and decimal keys. Press the decimal
Friday, November 07, 2008 138 Direct Access Use this feature to quickly access a channel with number tags. System or channel number tags can be set in
Friday, November 07, 2008 139 Key Operation During Scan Hold Mode Normal Mode [Scroll Control] knob Turn this knob to select the channel. [Scan / srch
Friday, November 07, 2008 14 PC Control You can download information into the scanner and control the scanner via your personal computer. LCD and Keyp
Friday, November 07, 2008 140 [FUNC] key Press this key to go to Function Mode with a 3-second timeout. The scanner displays the system number tag and
Friday, November 07, 2008 141 [1-3 / sr1-3] key Press this key to start searching the search range set at Set Search Key. [4 / LEFT / ifx] key Press t
Friday, November 07, 2008 142 PRIORITY SCAN There are two kinds of Priority Scan. (See: Set Priority) Refer to Set Priority for setting Priority Chann
Friday, November 07, 2008 143 Priority Plus Scan This works in Scan Mode or Scan Hold Mode when the setting of Priority Scan is Plus On. In this condi
Friday, November 07, 2008 144 PRIORITY ID SCAN Refer to Set Priority to set Priority Channels. Refer to Priority ID Scan for activation of Priority I
Friday, November 07, 2008 145 SEARCH MODE The scanner has Service Search, Custom Search and Quick Search in Search Mode. Display during Search Mode Th
Friday, November 07, 2008 146 Service Search You can search one of the pre-programmed search ranges. Publi c Safety 30. 8600MHz ↑ NFM The S
Friday, November 07, 2008 147 Custom Search Custom search can start by selecting Custom Search. When performing a custom search, you can turn on or of
Friday, November 07, 2008 148 Custom Search Range Select : You can select the range by turning [Scroll Control] in Function Mode. When the scanner ret
Friday, November 07, 2008 149 Receive LTR Control Channel: The scanner displays “LT System” and TGID. The scanner toggles the following display while
Friday, November 07, 2008 15 Design The below is a design reference. There might be some differences between this image and the actual final design.
Friday, November 07, 2008 150 Quick Search for frequency The scanner searches from the current channel frequency when the Quick Search starts from mon
Friday, November 07, 2008 151 Key Operation During Search Mode Normal Mode [Scroll Control] knob Turn this knob to change the searching direction. Whi
Friday, November 07, 2008 152 [1 - 3 / sr 1 - 3] key Press this key to start searching the search range set at Set Search Key. [4 / LEFT / ifx] Key Wh
Friday, November 07, 2008 153 SEARCH HOLD MODE Press [Hold / ] in Search Mode to go to Search Hold Mode and the scanner holds on the current frequenc
Friday, November 07, 2008 154 Quick Save Press [E / yes / gps] without entering data to quickly store the held frequency. This Quick Save function is
Friday, November 07, 2008 155 Key Operation During Search Hold Mode Normal Mode [Scroll Control] knob Turn this knob to change the searching directio
Friday, November 07, 2008 156 [L/O] key Press this key to go to Rvw Search L/O. [1 - 3 / sr 1 - 3] key Press this key to start searching the search ra
Friday, November 07, 2008 157 CLOSE CALL MODE The basic Close Call feature allows the scanner to immediately lock onto a transmission above a threshol
Friday, November 07, 2008 158 Press [Hold / ] to go to Close Call Hold Mode on the frequency. If the scanner gets a Close Call hit in GPS Mode, it di
Friday, November 07, 2008 159 Monitoring Close Call Transmission: While monitoring a Close Call transmission, the scanner displays "Close Call&qu
Friday, November 07, 2008 16 Controls and Keys “Long press” means pressing a key more than 2 second. Each key has a “normal” mode and a “Function” mod
Friday, November 07, 2008 160 Close Call Only The scanner performs this by menu at Close Call Only. Or, long press [Hold / ] in function mode to perf
Friday, November 07, 2008 161 Monitoring Close Call Transmission: In this monitoring state, the scanner does not check other Close Call transmissions.
Friday, November 07, 2008 162 If the scanner finds a Close Call transmission, it displays "CC Found!" on the first line. Then it performs du
Friday, November 07, 2008 163 When the scanner monitors or holds on a Close Call transmission, press [E / yes / gps] to quickly store the current freq
Friday, November 07, 2008 164 [Hold / ] key Press this key to set the Close Call Mode to off and go to Scan Mode. [L/O] key Press this key to go to R
Friday, November 07, 2008 165 [L/O] key Press this key to temporarily lock out the current frequency. When the scanner is turned off, the frequency is
Friday, November 07, 2008 166 [9 / mod] Key Press this key to change the modulation mode. [0 / WX] key Press this key to change WX Alert Priority Mode
Friday, November 07, 2008 167 WEATHER SCAN MODE You can start scanning the 10 Weather Channels either by using the menu or by pressing Function and lo
Friday, November 07, 2008 168 Warni ng WX WX Alert If the scanner is set to one of the SAME Groups, the scanner attemp
Friday, November 07, 2008 169 The scanner does not sound until it detects the 1050 Hz Weather Alert Tone or decodes the SAME data in Weather Alert Sca
Friday, November 07, 2008 17 Function + Scan / srch Key Press to resume searching. (Search Hold Mode and while monitoring in Search Mode) Press
Friday, November 07, 2008 170 Function Mode [SCAN / srch] key Press this key to display the prompt for starting Quick Search. The scanner displays the
Friday, November 07, 2008 171 [E / yes / gps] key Press this key to quickly store the current frequency. [MENU] key Press this key to go to the Menu M
Friday, November 07, 2008 172 TONE-OUT MODE Select “Tone-Out Standby” in Tone-Out for … Note: In this function, Close Call and WX Priority don't
Friday, November 07, 2008 173 Tone-Out Standby Mode If at least one of Tone A and Tone B have a programmed tone, the scanner goes to Tone-Out Standby.
Friday, November 07, 2008 174 Multi-Channel Monitoring The scanner can check multiple tone combination for channels that have the same settings for fr
Friday, November 07, 2008 175 Tone-Out Search Mode When both Tone A and Tone B are set to 0.0Hz, this channel will be treated as a Tone-Out Search cha
Friday, November 07, 2008 176 Tone-Out Hold Mode You can hear the transmission in Hold Mode. When the transmission ends and the delay time expires, th
Friday, November 07, 2008 177 Key Operation During Tone-Out Mode Normal Mode [Scroll Control] Knob Turn this knob to change the channel. Then the sca
Friday, November 07, 2008 178 Function Mode [Scan / srch] key Press this key to display the prompt for starting Quick Search. The scanner displays the
Friday, November 07, 2008 179 GPS MODE By connecting a GPS Unit, the scanner can operate the following functions. Automatic lockout control for Sca
Friday, November 07, 2008 18 Function + L/O Key Press once to temporarily lock out the current system, current site or current search range in Scan
Friday, November 07, 2008 180 Examples of each Display Mode are as follows. GPS DATA Display ETA Display Clock Display
Friday, November 07, 2008 181 Display Formats of Each Information: The advance direction: This is one of N, NE, E, SE, S, SW, W and NW. The time: Th
Friday, November 07, 2008 182 Display with Location Alert This shows Location Alert System Type. This shows that the scanner is in Location Alert. Th
Friday, November 07, 2008 183 The scanner alerts only once for each range when it meets both of the following two conditions. First condition is he
Friday, November 07, 2008 184 Priority for Location Alert When a Location Alert with a higher priority occurs during a Location Alert, the current Loc
Friday, November 07, 2008 185 F_POI__L / O_____GPS Revi ew_Locati on Hollywood RANGE: 0 . 1 0 M I L E __N _ 00º0 0 ' 0 0 . 0 0 __W 000º0
Friday, November 07, 2008 186 If you press [E / yes / gps], the scanner unlocks all locations of the current Type. If you press [. / no / pri], the
Friday, November 07, 2008 187 Key Operation During GPS Mode *Refer to Review Location Mode for Key Operation of Review Location Mode. Normal Mode [Scr
Friday, November 07, 2008 188 Function Mode [Scroll Control] knob Turn this knob to skip to the location that starts with the next alphabetic characte
Friday, November 07, 2008 189 BAND SCOPE MODE Band Scope Mode searches a frequency range and displays the signal level in real time. You can set the c
Friday, November 07, 2008 19 Function + 6 / RIGHT / disp Key Press to change the Display Mode. (Scan Hold Mode and Custom Search Mode) (Display mod
190 SRCH : This icon appears while in Search Mode. MAX : This icon appears while in MAX Hold Search Mode. This shows in the same place as &qu
191 Hold Mode You can monitor frequency displayed in this mode. The scanner displays "HOLD". Center frequency icon and bars do not blink dif
192 You can restart searching by pressing [FUNC] + [L/O]. The scanner also restarts searching if you change any parameter or search mode. In Hold Mode
193 Search Setting Parameters Center Frequency This parameter is the center frequency of the search range. *Please see: Band Coverage for acceptable f
194 Key Operation during Band Scope Mode Normal Mode during Normal Screen [Scroll Control] Knob Sets the level in Volume / Squelch Level Control mode.
195 [Scan / srch] Key Press this key in Search Mode to go to Max Hold Search Mode. Press this key in Max Hold Search Mode to go to Search Mode. In Hol
196 WIRED CLONE MODE You can clone almost all the data of one scanner to another. After connecting the two scanners, turn on the two scanners. Then se
197 Note: When you reboots the Slave Unit, the Unit will check and erase the protected systems first, this process may take a few minutes which depen
198 KEYLOCK Press [Func] + [ / / ] to lock or unlock the keypad. If you change this setting, the scanner displays "Keypad Lock" and &quo
199 KEY SAFE MODE This mode prevents accidentally changing parameter or modes. This mode is for handing the scanner to someone unfamiliar with its ope
Friday, November 07, 2008 2 Contents Feature Summary ...
Friday, November 07, 2008 20 Menu Key Press to enter the Menu Mode. Press to go back up one menu level when in the Menu Mode. Press after ent
200 Key Safe Operation Turns on power supply while pressing and holding [FUNC] key to go to the LAST MODE* in Key Safe Mode. The scanner displays the
201 MEMORY INITIALIZATION Press and hold [2 / sr 2], [9 / mod] and [Hold / ] and turn on the scanner to initialize the Memory and be able to restore
202 BATTERY CHARGE Battery Type Select You can power the scanner non-rechargeable batteries (not supplied), nickel metal hydride (Ni-MH) rechargeable
203 The scanner displays "Pre-Charging". "Pre-Charging" is a transition to the beginning of “Normal Charging”. Pre- Chargi ng Wh
204 If the scanner detects an illegal voltage (voltage outside the allowable range), it displays “Illegal Voltage” and you cannot turn on power. I ll
205 OTHERS AVAILABLE SYSTEM SETTINGS Different types of systems and sites have different settings available. *In the following table, "CNV"
206 Site Settings Site Setting P25 MOT EDACS LTR Standard Trunk One-Freq Trunk WIDE / NARROW SCAT Edit Name O O O O --- O Set Quick Key O O O O O O S
207 Channel Settings Channel Settings CNV* P25 MOT EDACS LTR Standard Trunk One-Freq Trunk WIDE / NARROW SCAT Edit Name O O O O O --- O Edit Frequency
208 TGID FORMAT FOR TRUNKED SYSTEM [ MOTOROLA TYPE1 SYSTEM ] Display Format 1) BFF-SS Normal ID B is 1 digit FF is 2 digi
209 Range B : BLOCK (0-7) FF(F) : FLEET S(S) : SUB-FLEET FLEET and SUB-FLEET maximum numbers depend on the SIZE CODE of
Friday, November 07, 2008 21 Displays LCD Design The reference design shown below is for illustration purposes only and is not intended to be a photor
210 [ MOTOROLA TYPE2 SYSTEM ] <Decimal Format> Display Format 1) NNNNN Normal ID NNNNN is 1-5 digit(s) 2) iNNNNN I
211 [ MOTOROLA P25 SYSTEM ] <Decimal Format> Display Format 1) NNNNN Normal ID NNNNN is 1-5 digit(s) 2) iNNNNNNNN I
212 [ EDACS SYSTEM ] <AFS format> Display Format 1) AA-FFS Normal ID AA is 2 digits (0 filling) FF is 2 digits (0
213 <Decimal format> Display Format 1) NNNN Normal ID NNNN is 1-4 digit(s) (no 0 filling) 2) iNNNNN I-CALL ID
214 [ LTR SYSTEM ] Display Format 1) A-RR-NNN Normal ID A is 1 digit RR is 2 digits NNN is 3 digits 2) A-RR-
215 FLEET MAP The range of TGIDs is from 0 to 65535. This range is split into 8 equal blocks, and each Block is set to one of 15 Size Codes. The ran
216 Details of each Size Code are as follows. Size Code Fleet-SubFleet-ID Number of Blocks occupied 0 (as Type II ID) 1 1 128-4-16 1 2 16-8-64 1 3 8-8
217 WEATHER CHANNELS The modulation for all Weather Channels is FM. CH No. Frequency 1 162.5500 MHz 2 162.4000 MHz 3 162.4750 MHz 4 162.4250 MHz 5 162
218 CEA2009-SAME EVENT CODE(ANSI/CEA-2009-A October 2005) Standard Event Code EVENT LEVEL LCD Display Warning Watch Advisory ADR Administrative Mess
219 LSW Land Slide Warning O Land Slide NAT National Audible Test O National Audible NIC National Information Center O National Info NMN Network
Friday, November 07, 2008 22 LNK: This icon appears when data is received on a VOICE CHANNEL. This shows in the same place as "P25". DAT:
220 REMOTE COMMAND 【 Remote Communication Format 】 BPS rate : 4800/9600/19200/38400/57600/115200 bps Start/Stop bit : 1 bit, 1 bit Data Length : 8
221 12. [LONGITUDE] shows West or East Longitude. The data shows “DDDMMSSssL” at DMS Format. DDD : Degree ( 000 - 180 : Triple figure fixation
222 TFQ Get/Set Trunk Frequency Info O AGC Append Channel Group O AGT Append TalkGroup ID Group O DGR Delete Group / Site O GIN Get/Set Group Inf
223 <COMMAND GID> Get Current TGID Status Controller → Radio GID[\r] Radio → Controller GID,[SITE_TYPE],[TGID],[ID_SRCH_MODE],[NAME1],[NAM
224 <COMMAND KEY> Push KEY Controller → Radio KEY,[KEY_CODE],[KEY_MODE][\r] Radio → Controller KEY,OK[\r] [KEY_CODE] M : MENU F
225 <COMMAND POF> Power OFF Controller → Radio POF[\r] Radio → Controller POF,OK[\r] Turns off the scanner. After this command, t
226 FUNCTION UASD specifies arbitrary frequency and changes to Quick Search Hold (VFO) mode. Parameter, such as STP, changes the contents of Srch/Clo
227 This command is invalid when the scanner is in Menu Mode, during Direct Entry operation, during Quick Save operation. FUNCTION UASD specifies arb
228 <COMMAND STS> Get Current Status Controller → Radio STS[\r] Radio → Controller STS,[DSP_FORM],[L1_CHAR],[L1_MODE],[L2_CHAR],[L2_MODE],
229 , ← [L3_MODE] Srch/CloCall Opt, ← [L4_CHAR] , ← [L4_MODE] 1,0,0,0,,,0,GREEN,,[\r] Returns
Friday, November 07, 2008 23 Tones The scanner can produce 3 fundamental tones, high (1200 Hz), middle (920 Hz), and low (640 Hz). Furthermore, there
230 [SYS_TAG] : Current system number tag (0-999/NONE) [CHAN_TAG] : Current channel number tag (0-999/NONE) [P25NAC] : P25 NA
231 <COMMAND MNU> Menu Mode Controller → Radio MNU,[MENU_INDEX][\r] Radio → Controller MNU,OK[\r] [MENU_INDEX] : SVC_MENU : Serv
232 <COMMAND PRG> Enter Program Mode Controller → Radio PRG[\r] Radio → Controller PRG,OK[\r] PRG,NG[\r] This command is invalid when the
233 <COMMAND BSV > Get/Set Battery Info Controller → Radio BSV [\r] BSV,[BAT_SAVE],[CHARGE_TIME][\r] Radio → Controller BSV, [BAT_SAVE],[
234 <COMMAND KBP> Get/Set Key Beep and setting Controller → Radio KBP[\r] KBP,[LEVEL],[LOCK],[SAFE][\r] Radio → Controller KBP,[LEVEL],[LO
235 <COMMAND AGV> Get/Set Auto Gain Control Controller → Radio AGV[\r] AGV,[RSV],[RSV],[A_RES],[A_REF],[A_GAIN],[D_RES],[A_GAIN] [\r]
236 <COMMAND QSL> Get/Set System/Site Quick Lockout Controller → Radio QSL[\r] QSL,[PAGE0],[PAGE1],[PAGE2],[PAGE3],[PAGE4],[PAGE5],[PAGE6]
237 <COMMAND CSY> Create System Controller → Radio CSY,[SYS_TYPE],[PROTECT][\r] Radio → Controller CSY,[SYS_INDEX][\r] [SYS_TYPE] :
238 <COMMAND SIN> Get/Set System Info Controller → Radio SIN,[INDEX][\r] SIN,[INDEX],[NAME],[QUICK_KEY],[HLD],[LOUT],[DLY],[RSV],[RSV],[RSV]
239 <COMMAND TRN> Get/Set Trunk Info Controller → Radio TRN,[INDEX][\r] TRN,[INDEX],[ID_SEARCH],[S_BIT],[END_CODE],[AFS],[RSV],[RSV],[EMG]
Friday, November 07, 2008 24 Tones in Menu Mode Selecting a menu item As you step to the next menu item by turning [Scroll Control] knob, the scanner
240 <COMMAND AST> Append Site Controller → Radio AST,[SYS_INDEX],[RSV][\r] Radio → Controller AST,[SITE_INDEX][\r] [SYS_INDEX] :
241 The scanner returns only "," to punctuate for parameters which are not appropriate the site type. In set command, the scanner neglects
242 <COMMAND ABP> Get/Set APCO-P25 Band Plan Controller → Radio ① ABP,[INDEX][\r] ② ABP,[INDEX],[BASE_FREQ_0],[SPACING_FREQ_0],[BASE
243 <COMMAND TFQ> Get/Set Trunk Frequency Info Controller → Radio TFQ,[CHN_INDEX][\r] TFQ,[CHN_INDEX],[FRQ],[LCN],[LOUT],[RSV],[NUMBER_TAG],
244 <COMMAND AGT> Append TGID Group Controller → Radio AGT,[SYS_INDEX][\r] Radio → Controller AGT,[GRP_INDEX][\r] [SYS_INDEX] : Sys
245 Get/Set Group Information. In set command, only "," parameters are not changed. The set command is aborted if any format error is detec
246 <COMMAND CIN> Get/Set Channel Info Controller → Radio CIN,[INDEX][\r] CIN,[INDEX],[NAME],[FRQ],[MOD],[CTCSS/DCS],[TLOCK],[LOUT],[PRI],
247 <COMMAND TIN> Get/Set TGID Info Controller → Radio TIN,[INDEX][\r] TIN,[INDEX],[NAME],[TGID],[LOUT],[PRI],[ALT],[ALTL],[RSV],[AUDIO_TY
248 <COMMAND SLI> Get Search L/O TGID Controller → Radio SLI,[SYS_INDEX][\r] Radio → Controller SLI,[TGID][\r] SLI,-1[\r] : No more l
249 <COMMAND FWD> Get Fwd Index Controller → Radio FWD,[INDEX][\r] Radio → Controller FWD,[INDEX][\r] [INDEX] : Index of system, site,
Friday, November 07, 2008 25 Operation NOTE: Valid keys for the "Press Any Key" prompt are all keys except for [ / / ]. Pressing [ /
250 <COMMAND LIT> Get Location Alert System Index Tail Controller → Radio LIT,[LAS_TYPE][\r] Radio → Controller LIT,[INDEX][\r] [LAS_
251 <COMMAND LIN> Get/Set Location Alert System Info Controller → Radio LIN,[INDEX][\r] LIN,[INDEX],[LAS_TYPE],[NAME],[LOUT],[ALT],[ALTL],
252 <COMMAND SCO> Get/Set Search/Close Call Settings Controller → Radio SCO[\r] SCO,[RSV],[MOD],[ATT],[DLY],[RSV],[CODE_SRCH],[BSC],[REP],
253 <COMMAND SHK> Get/Set Search Key Settings Controller → Radio SHK[\r] SHK,[SRCH_KEY_1],[SRCH_KEY_2],[SRCH_KEY_3],[RSV],[RSV],[RSV][\r]
254 <COMMAND LOF > Lock Out Frequency Controller → Radio LOF,[FRQ][\r] Radio → Controller LOF,OK[\r] [FRQ] : Frequency (250000-
255 <COMMAND SSP> Get/Set Service Search Settings Controller → Radio SSP,[SRCH_INDEX][\r] SSP,[SRCH_INDEX],[DLY],[ATT],[HLD],[LOUT],[QUICK
256 <COMMAND CBP> Get/Set C-Ch Only Custom Search MOT Band Plan Settings Controller → Radio CBP,[SRCH_INDEX][\r] CBP,[SRCH_INDEX],[MOT_TYP
257 <COMMAND CSP> Get/Set Custom Search Settings Controller → Radio CSP,[SRCH_INDEX][\r] CSP,[SRCH_INDEX],[NAME],[LIMIT_L],[LIMIT_H],[STP]
258 <COMMAND WXS> Get/Set Weather Settings Controller → Radio WXS[\r] WXS,[DLY],[ATT],[ALT_PRI],[RSV],[AGC_ANALOG],[RSV][\r] Radio → Con
259 <COMMAND TON> Get/Set Tone-Out Settings Controller → Radio TON,[INDEX][\r] TON,[INDEX],[NAME],[FRQ],[MOD],[ATT],[DLY],[ALT],[ALTL],[TO
Friday, November 07, 2008 26 Volume and Squelch Control Volume and Squelch can be adjusted by rotating the [Scroll Control] in the following modes: Sc
260 <COMMAND SCN> Get/Set Scanner Option Settings Controller → Radio SCN[\r] SCN,[DISP_MODE],[RSV],[CH_LOG],[G_ATT],[RSV],[P25_LPF][RSV],[R
261 <COMMAND DBC> Get/Set Default Band Coverage Settings Controller → Radio DBC,[BNAD_NO][\r] DBC,[BNAD_NO],[STEP],[MOD][\r] Radio → Co
262 <COMMAND BSP> Get/Set Band Scope System Settings Controller → Radio BSP[\r] BSP,[FRQ],[STP],[SPN],[MAX_HOLD][\r] Radio → Controller
263 <COMMAND CIE> Clear IF exchange Frequency Controller → Radio CIE,[FRQ][\r] Radio → Controller CIE,OK[\r] [FRQ] : IF Exchange Fr
264 CTCSS/DCS CODE LIST CTCSSMODE CODE CTCSS 67.0Hz 64 CTCSS 69.3Hz 65 CTCSS 71.9Hz 66 CTCSS 74.4Hz 67 CTCSS 77.0Hz 68 CTCSS 79.7Hz 69 CTCSS 82.5Hz 70
265 FONT DATA Character pattern of 8 x 16 dot This character pattern is Large Font. *In this document, characters of these areas are described as n
266
Friday, November 07, 2008 27 P25 Condition Mode Press [Function] + [Scroll Control] key to go to P25 Condition mode in Volume / Squelch Adjust mode. Y
270
271 Character pattern of 8 x 8 dot This character pattern is Small Font.
272
273
Friday, November 07, 2008 28 Menu Mode General Operations Key Operation To enter the Menu Mode: Press [Menu] To select a Menu item: Turn [Scroll Con
Friday, November 07, 2008 29 Edit Name The editing cursor is displayed. Turn [Scroll Control] to choose the character and the cursor stays at the high
Friday, November 07, 2008 3 IF Exchange ...
Friday, November 07, 2008 30 Edit Frequency and Set Tone The editing cursor is displayed. Press a number key to enter each digit and press the decimal
Friday, November 07, 2008 31 Hexadecimal TGID edit Turn the [Scroll Control] to select Hexadecimal characters from “0” to “F”, Press [4 / LEFT / ifx]
Friday, November 07, 2008 32 Top Menu Press [MENU] key to go to Menu Mode. Top Menu has the following items. Program System Program Location Srch/Clo
Friday, November 07, 2008 33 Creating a New System You can create up to 500 systems. To create a new system, select the system type from the following
Friday, November 07, 2008 34 System Settings This menu has the following items. Edit Name Edit Sys Option Edit Site Edit Group Copy System Delete Syst
Friday, November 07, 2008 35 Edit Sys Option You can change the following System settings. Set Quick Key Set Startup Key Set Number Tag Set Lockout Se
Friday, November 07, 2008 36 Set Number Tag The System Number Tag can be set in this menu. Press a number key to input the number tag. Press [. / no /
Friday, November 07, 2008 37 Set Delay Time This setting controls how long the scanner stays on a transmission before resuming scanning. If you select
Friday, November 07, 2008 38 Custom On the other hand, if "Custom" is selected, then you are prompted to enter the Fleet Map information. Yo
Friday, November 07, 2008 39 Set End Code This setting determines how the scanner treats the transmission end code. Analog The scanner pays attenti
Friday, November 07, 2008 4 Alert for Point Of Interest ... 24 A
Friday, November 07, 2008 40 Set Alert Light If “Set Alert Light” is selected, you can select from the following alert colors: Off Blue Red Magenta G
Friday, November 07, 2008 41 Rvw ID:Srch L/O Allows you to review TGIDs that are locked out in ID Search or ID Scan. Any TalkGroup in this list will b
Friday, November 07, 2008 42 Clr All L/O IDs Selecting this causes the scanner to prompt "Confirm ?" and "Unlock All(Y/N)". Confi
Friday, November 07, 2008 43 P25 Waiting Time The feature is used to set a wait time for P25 decode. After receive a transmission the scanner will wai
Friday, November 07, 2008 44 Copy System You can copy the System and all associated settings by select this menu item. The scanner prompts you for a n
Friday, November 07, 2008 45 Program Site You can select an existing Site for editing or create a new Site. Site Names that already have been created
Friday, November 07, 2008 46 Edit Name You can name the site. Refer to FONT DATA for the characters that can be entered. Press [E / yes / gps] to acce
Friday, November 07, 2008 47 If you enter less than “125Hz”, the scanner prompts “Out of Range" and "Set Min? (Y/N)”. Press [E / yes / gps]
Friday, November 07, 2008 48 When you select ”Set Spacing”, the following spacing values can be selected: 5.00 kHz 6.25 kHz 10.00 kHz 12.50
Friday, November 07, 2008 49 If "New Frequency" is selected by pressing [E / yes / gps], the scanner skips the next selection. Then it goes
Friday, November 07, 2008 5 Quick Save for CTCSS/DCS/P25 NAC Data ... 128 Key Operation During
Friday, November 07, 2008 50 Set Number Tag The channel Number Tag can be set in this menu. Press a number key to input the number tag. Press [. / no
Friday, November 07, 2008 51 Set Modulation You can select the modulation from following settings. Auto* The scanner uses the modulation normal for t
Friday, November 07, 2008 52 Set Lati tude 00. 000000 N Set C-Ch Only You can select how the scanner tracks Motorola Systems. (C-Ch me
Friday, November 07, 2008 53 Set Longi tude 00. 000000 W Set Longitude Press the number keys to enter longitude data. Press any number
Friday, November 07, 2008 54 P25 Waiting Time The feature is used to set a wait time for P25 decode. After receive a transmission the scanner will wai
Friday, November 07, 2008 55 Program Group This menu lets you select a Channel Group for programming or create a new Channel Group. Names of Groups al
Friday, November 07, 2008 56 Set Quick Key This option lets you select which Group Quick Key will rapidly enable/disable the Group when the scanner is
Friday, November 07, 2008 57 If “DEG:DDD.dddddd” is selected in Set Pos Format, the display is the following. Set Longitude Enter the longitude da
Friday, November 07, 2008 58 Set GPS Enable When this option is set to “On”, the scanner will control the L/O status of this channel group using posit
Friday, November 07, 2008 59 Program Channel You can select a Channel for programming or add a new Channel. Names of Channels already added are displa
Friday, November 07, 2008 6 Close Call Auto Store ... 161
Friday, November 07, 2008 60 Input TGID: You must enter a TGID. You can input only a TGID in the format suitable for the site type. Motorola Type ID
Friday, November 07, 2008 61 EDACS ID : For EDCS Wide/Narrow systems. Press the number keys to enter the Agency number. Press the decimal key to enter
Friday, November 07, 2008 62 Channel Settings The following settings are available for channels. Edit Name Edit Frequency Edit TGID Set Audio Type Set
Friday, November 07, 2008 63 Set Audio Type You can select an audio type for each channel. All The scanner receives both Digital and Analog sign
Friday, November 07, 2008 64 If you select “Set Lockout”: You can select a CTCSS or DCS for lockout. Turn [Scroll Control] to select and press [E / y
Friday, November 07, 2008 65 Set Alert Channel alert options can be set using this menu. Set Alert Tone Set Alert Light Press [E / yes / gps] to ente
Friday, November 07, 2008 66 Set Lockout This option allows you to lock or unlock the current channel. When the channel is locked out, the scanner doe
Friday, November 07, 2008 67 Program Location You can select the any Location for programming or create a new Location. First, select the location typ
Friday, November 07, 2008 68 Set Type This option can be used to select the location type. POI Dangerous Xing Dangerous Road Turn [Scroll Control] to
Friday, November 07, 2008 69 Set Alert Volume This option can be used to set the alert level. Auto The alert is set to the same volume as normal
Friday, November 07, 2008 7 Error State ...
Friday, November 07, 2008 70 Set Range This option sets the range for a POI. In this menu, the setting unit depends on the setting in Set Unit. When
Friday, November 07, 2008 71 Set Lockout This option allows you to lock or unlock the current location. When the location is locked out, the scanner d
Friday, November 07, 2008 72 Srch/CloCall Opt This menu includes the following: Freq Lockouts Broadcast Screen Tone/Code Search Repeater Find Max Auto
Friday, November 07, 2008 73 Freq Lockouts You can select from these items. Unlock All Rvw Search L/O Press [E / yes / gps] to enter each menu. Unlock
Friday, November 07, 2008 74 Broadcast Screen This option sets whether the scanner screens broadcast frequencies. You can select the following items.
Friday, November 07, 2008 75 Program Band You can set up to 10 custom band screens. Select a band and press [E / yes / gps] to go to the limit setting
Friday, November 07, 2008 76 Max Auto Store This setting controls how many hits the scanner will automatically store in either Search and Store or Clo
Friday, November 07, 2008 77 Set Audio AGC When Audio AGC function is “On”, the scanner judges the volume level and changes the volume automatically.
Friday, November 07, 2008 78 Search for... This menu includes the following items. Service Search Edit Service Custom Search Edit Custom Search and St
Friday, November 07, 2008 79 Set Delay Time This setting controls how long the scanner stays on frequencies after a transmission ends before resuming
Friday, November 07, 2008 8 Feature Summary Band Coverage Frequency (MHz) Modulation Step (kHz) Remark Lower Edge Upper Edge 25.0000 26.9600 AM 5.0 Pe
Friday, November 07, 2008 80 P25 Waiting Time The feature is used to set a wait time for P25 decode. After receiving a transmission the scanner will w
Friday, November 07, 2008 81 Press [E / yes / gps] to accept the setting and return to the previous menu. Note: The valid setting range is from 0 to
Friday, November 07, 2008 82 Edit Custom You can edit the 10 Custom Search Ranges. Names of Custom Search Ranges are displayed as Menu items. For exam
Friday, November 07, 2008 83 Set Delay Time This setting controls how long the scanner stays on frequencies after a transmission ends before resuming
Friday, November 07, 2008 84 Set C-Ch Only These options let you set whether the scanner tracks talk group activity when it detects a Motorola or LTR
Friday, November 07, 2008 85 P25 Waiting Time The feature is used to set a wait time for P25 decode. After receive a transmission the scanner will wai
Friday, November 07, 2008 86 Search and Store This function lets the scanner search for new frequencies in Custom Search Ranges or Service Search Rang
Friday, November 07, 2008 87 For Trunked System If a trunked System is selected, you will be asked to select a site. If no site is stored in that syst
Friday, November 07, 2008 88 If the Memory is full, it displays "Memory Full" on the second line and sounds an Error Tone. It does not exit
Friday, November 07, 2008 89 Close Call This menu has the following items. Close Call Only CC Auto Store Hits with Scan Set CC Mode Set CC Override S
Friday, November 07, 2008 9 Channels Dynamic – You can create up to 25,000 total conventional channels, trunked channels, and trunked system frequenci
Friday, November 07, 2008 90 Set Number Tag Number Tag can be set in this menu. Press a number key to input the number tag. Press [. / no / pri] to cl
Friday, November 07, 2008 91 Set CC Override This mode determines how the scanner will behave when a Close Call signal is detected. On The scanner al
Friday, November 07, 2008 92 Set Alert Light You can set whether the scanner should have an alert light when it gets a Close Call hit. Off Blue Red Ma
Friday, November 07, 2008 93 Set CC Bands This setting controls the band filtering used during Close Call operation. You can turn on or off the follow
Friday, November 07, 2008 94 Priority Scan You can set following items in this menu. Set Priority Set Interval MaxCHs/Pri-Scan Press [E / yes /
Friday, November 07, 2008 95 WX Operation This menu lets you set the following items. Weather Scan Weather Alert Program SAME Set Delay Time Set Atten
Friday, November 07, 2008 96 Program SAME You can edit the 5 SAME Groups. The names of SAME Groups are displayed as Menu Items. Default names as follo
Friday, November 07, 2008 97 Set Delay Time This setting controls how long the scanner stays on the Weather Channel after a transmission ends before r
Friday, November 07, 2008 98 Tone-Out for … This menu lets you set the following items. Tone-Out Standby Tone-Out Setup Select “Tone-Out Standby” to s
Friday, November 07, 2008 99 Set Frequency You can set the following items. Edit Frequency Set Modulation Set Attenuator Press [E / yes / gps] to go t
Kommentare zu diesen Handbüchern