ANA 9710900 MHz AnalogPBXCordless TelephoneOperating Guide®
About Your ANA 9710Congratulations on your purchase of the Uniden ANA 9710 CordlessTelephone. The ANA 9710 is designed and engineered to exactingstand
Important Electrical ConsiderationsWarning: Please do not attempt to unplug any applianceduring an electrical storm.Unplug all electrical appliances w
Radio InterferenceRadio interference may occasionally cause buzzing and hummingin your cordless Handset, or clicking noises in the Base Unit. Thisinte
ANA 9710 FeaturesSuper Long Range 900MHz Digital Spread Spectrum2-line, 16-digit LCD DisplayHeadset JackRinger Volume ControlHandset Volume ControlSin
Installing Your ANA 9710Selecting the Installation LocationSelect a location for the ANA 9710 that avoids excessive heat orhumidity. The Base Unit of
Connecting the Telephone CordsThe ANA 9710 must be connected to an analog PBX port or astandard analog telephone line.CAUTION:Never install telephone
Tone/Pulse SwitchBe sure the TONE/PULSE switch is in the TONE position.Note: Most systems are Tone dialing. Check with your PBXAdministrator if you ar
IMPORTANT! Place the power cord so that it does not create a triphazard, or where it could become chafed and create a fire or otherelectrical hazards.
Wall InstallationStandard Wall Plate MountingThis Phone is designed to be mounted on a standard AT&T or GTEwall plate. To attach the wall mount st
6. Place the Base Unit on the postsof the wall plate and push downuntil it’s firmly seated.7. Plug the AC Adapter into astandard 120V AC wall outlet.N
One Year Limited WarrantyWARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)ELEMENTS OF WARRANTY: Uniden warrants, for one year, to theoriginal retail ow
1. Insert two mounting screwsinto the wall 3-15/16 inchesapart. Allow about 3/16 of aninch between the wall andscrew heads for mounting thephone.2. Pl
5. Plug the other end of the shorttelephone cord into a telephonewall jack.6. Plug the AC Adapter into a standard 120V AC wall outlet byfollowing step
3. Place the Charging Uniton the posts of the wallscrews and push downuntil it is firmly seated.4. Plug the AC Adapter into astandard 120V AC wall out
Attaching the Beltclip to the HandsetYou can use the Beltclip to attach the Handset to your belt or pocketfor convenient portability.1. Slide the clip
3. To remove, simply press theretain clip in toward theBeltclip blade and slide theclip up at the same time.Installing the Handset Battery Pack1. Remo
3. Securely close the batterycompartment cover by sliding itup until it snaps into place.Charging the Handset Battery PackThe Rechargeable Nickel-Cadm
Charging Spare Battery PacksThe Charger Unit of your ANA 9710 is equipped to charge theSpare Battery Pack with or without the Handset in the front slo
Cleaning the Battery and Charging Unit ContactsTo maintain a good charge, it is important to clean all chargingcontacts on the Handset, Spare Battery
ANA 9710 Handset ControlsEarpiece VolumePressr/volon the side of the Handset during a call to change theearpiece volume on the handset.22
Handset Ringer tone and volumePressr/volon the side of the Handset in Standby mode to selectseven ringer tones and volume combinations.Vibrate Mode“Ri
Covered under one or more of the following U.S. patents:4,511,761 4,523,058 4,595,795, 4,597,1044,797,916 4,803,491 5,381,460 5,426,6905,434,905 5,491
Using the HandsetWhen you pick up the Handsetand presstalk, you will see:After the connection has beenmade between the Handset andBase, you will see:O
Answering a CallWhen you receive a call, the Handsetrings and you will see:Handset in the Charging Unit Handset out of Charging UnitPick up the Handse
Feature ButtonsNote: The exact operation of the Feature Buttons depends on howyour PBX system is configured. Contact your PBXAdministrator for more in
Programming the Feature ButtonsThe Transfer and Conference Keys can be programmed for specialuse, such as causing a “Hook Flash” followed by a special
Function KeysHOLDPress once, you will hear a “beep” and the call is placed on hold.Pressholdortalkto resume the call (local hold).XFERPressxfer(Transf
Using Your ANA 9710 MemoryUse these buttons to operate theANA 9710 MemoryStoring a Number1. Pressmem. You will hear a beep,and see the message:2. Ente
5. The ANA 9710 then returns to Standby mode.Example: Store 555-1234 in memory location 12:A. Pressmem.B. Enter5551234.C. Pressmem.D. Press12.The Hand
Dialing with a Stored NumberNote: The following applies when the phone is in Standby Mode, andyou have already established a connection between theHan
C. Pressing themutekey, youwill move down through theMemory (20 to 1). Pressingr/volyou will move up throughthe Memory (1 to 20). Pressr/volormuteunti
Using Your ANA 9710 Base UnitAlthough most of the ANA 9710 operations are performed at theHandset, there are two operations performed at the Base Unit
PRECAUTIONSBefore you read anything else,please observe the following:WARNING!Uniden America Corporation DOES NOT represent this unit tobe waterproof.
Optional Headset (EXP9530)The optional Headset provides a “Hands-Free” Option for theANA 9710. With the Headset installed, you can use the Beltclipto
Using an Optional Second 2500-typeAnalog TelephoneAnalog TelephoneA standard 2500-type Desk telephone can be used with theANA 9710. Calls can then be
Typical ApplicationsYou can use the ANA 9710 together with a standard PBXtelephone to give you effective business communications both atyour desk and
Optional Accessories and Replacement PartsFor the following Optional Accessories and Replacement Parts contactyour PBX Administrator.37EXP9704 ACAdapt
TroubleshootingIf your ANA 9710 Cordless Telephone is not performing to yourexpectations, please try these simple steps. If you are still unableto res
SpecificationsGeneral: The ANA 9710 complies with FCC and ICparts 15 and 68.Frequency Control : Phase Lock LoopModulation : Spread SpectrumOperating T
MEMO40
Handset Controls & Functions1. Ringer ON/OFF switch2. Message Display3. Hold (hold) Key4. Talk (talk) Key5. Numeric Keypad6. Pause (pause) Key7. R
Base Unit Controls & Functions18. DC Power Jack19. Hold (hold) Key20. Page/find (page/find) Key21. Tone/Pulse Switch
Uniden® is a registered trademark of Uniden America Corporation.AutoStandby™ and AutoTalk™ are trademarks of Uniden America Corporation.AutoStandby is
Important Safety InstructionsWhen using your telephone equipment, basic safety precautionsshould always be followed to reduce the risk of fire, electr
D. If the product does not operate normally when following theoperating instructions. Adjust only those controls that arecovered by the operating inst
Kommentare zu diesen Handbüchern