Uniden ANA9320 Bedienungshandbuch

About Your ANA 9320Congratulations on your purchase of the Uniden ANA 9320Cordless Telephone. The ANA 9320 is designed and engineeredto exacting stand

Important Electrical ConsiderationsWarning: Please do not attempt to unplug any applianceduring an electrical storm.Unplug all electrical appliances w

Radio InterferenceRadio interference may occasionally cause buzzing and hummingin your cordless Handset, or clicking noises in the Base Unit.This inte

ANA 9320 FeaturesnLong Range 900MHz Digitaln2-line, 16-digit LCD DisplaynRinger Volume ControlnHandset Volume ControlnSingle button access to: CONFERE

Installing Your ANA 9320Selecting the Installation LocationSelect a location for the ANA 9320 to avoid excessive heat orhumidity. The Base Unit of you

Connecting the Telephone CordsThe ANA 9320 must be connected to a PSTN or an analog PBXport telephone line.TIP: To setup PSTN or PBX, refer to page 24

Applying Power to the Base and Charger UnitsUse only the supplied AC Adapter: EXP9704IMPORTANT! Route the power cord where it will not create a tripha

Wall InstallationStandard Wall Plate MountingThese Phones are designed to be mounted on a standard wall plate.To attach the wall mount stand to the Ba

6. Place the Base Unit on the postsof the wall plate and push downuntil it’s firmly seated.7. Plug the AC Adapter into astandard 120V AC wall outlet.N

1. Insert two mounting screws3 15/16 inches apart. Allow about3/16 of an inch between the walland screw heads for mountingthe phone.2. Plug and secure

One Year Limited WarrantyWARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)ELEMENTS OF WARRANTY: Uniden warrants, for one year, to theoriginal retail ow

Charging Unit Wall MountingThe Charging Unit is also designed to be wall mounted.Before mounting your charging unit, consider the following:nSelect a

3. Slide the wall mount stand intothe notches on the bottom ofthe charging unit.4. Place the Charging Uniton the posts of the wallscrews and push down

Attaching the Belt Clip to the HandsetYou can use the Belt Clip to attach the Handset to your belt or pocketfor convenient portability.1. Snap the tab

Installing the Handset Battery Pack1. Remove the battery cover bypressing the latch and slidingthe cover down and off ofthe Handset.2. Connect the bat

Charging the Handset Battery PackThe Rechargeable Ni-MH Battery Pack must be fully charged beforeusing your ANA 9320 for the first time.(Note: Charge

Using Your ANA 9320 HandsetBefore using your ANA 9320, be sure to raise the antenna to thevertical position.Note: Operation of the ANA 9320 is perform

Earpiece VolumePressRING/VOLon the side of the Handset during a call to select theearpiece volume of the handset.2028Y:...ANA9320 om.vpTue Dec 03 15:2

Handset Ringer Tone and VolumePressingRING/VOLon the side of the Handset in standby modeto select seven ringer tones and volume combinations.Vibrate M

Using the HandsetWhen you pick up the Handset andpressTALK, you will see:After the connection has beenmade between the Handset andBase, the display wi

Answering a CallWhen you receive a call, theHandset rings and you’ll see:Handset in the Charging Unit Handset out of Charging UnitPick up the Handset.

Programming FunctionsPBX or PSTNIn the Programming mode, you can select either Analog PBX or PSTN(Public Service Telephone Network) operation. The def

Programming Xfer in PBXNote: Before programming these commands, contact yourPBX Administrator to obtain programming codes.Thexferkey can be programmed

Programming Conf in PBXYour PBX system's configuration determines how the conferencefeature works. Contact your PBX Administrator for exact opera

Feature ButtonsNote: The exact operation of the Feature Buttons depends on howyour PBX system is configured. Contact your PBX Administratorfor more in

PBX FeaturesL1KeyPress theL1key to initiate a call on Line 1.L2KeyPress theL2key to initiate a call on Line 2.confKeyIn PBX mode, theconf(conference)

RING/VOL KeyThis key selects the ringer volume level or tone (or silent alert)during standby mode, and handset earpiece audio levelduring a call. This

xferKeyNote: This feature is not available in PSTN mode.holdKeyPress once and the call is placed on hold.PressL1,L2orTALKto resume the call.pauseKeyPr

Optional Headset (EXP9730/EXP9530)The optional Headset provides a “Hands-Free” Option for theANA 9320. With the Headset installed, you can use the Bel

Optional Accessories and Replacement PartsFor the following Optional Accessories and Replacement Partscontact your PBX Administrator.32EXP9704 ACAdapt

TroubleshootingIf your ANA 9320 Cordless Telephone is not performing to yourexpectations, please try these simple steps. If you are still unableto res

PRECAUTIONSBefore you read anything else,please observe the following:WARNING!Uniden America Corporation DOES NOT represent this unitto be waterproof.

SpecificationsFrequency Control : Phase Lock LoopModulation : FMOperating Temperature : 0° to 50° C (+32° F to +122° F)Base UnitReceive/Transmit Frequ

MEMO3543Y:...ANA9320 om.vpTue Dec 03 15:25:59 2002Color profile: DisabledComposite Default screen

Handset Controls & Functions1. Headset Jack2. Message Display3. Pause (pause) Key4. Talk (TALK) Key5. Numeric Keypad6.L2Key7.L1Key8. Microphone9.

Base Unit Controls & Functions18.line 1LED19.power/statusLED20.line 2LED18 20197Y:...ANA9320 om.vpTue Dec 03 15:21:27 2002Color profile: DisabledC

1TABLE OF CONTENTSImportant Safety Instructions...2About Your ANA 9320...

Important Safety InstructionsWhen using your telephone equipment, basic safety precautionsshould always be followed to reduce the risk of fire, electr

D. If the product does not operate normally when following theoperating instructions. Adjust only those controls that arecovered by the operating inst